loubyscooby Posted August 26, 2016 Report Share Posted August 26, 2016 (edited) Does anyone know the approximate costs of having steel panels welded around the stern. I'd like to have the lower section below the handrail enclosed and having recently been given an astronomical quote for something I knew nothing about I'm now a tad wary. The boat is 10ft wide. Thanks in advance. Edited August 26, 2016 by loubyscooby Link to comment Share on other sites More sharing options...
MtB Posted August 26, 2016 Report Share Posted August 26, 2016 How elaborate are you wanting this to be? Just three panels cut to shape and welded in to place would cost perhaps £500 or so. If you want them and the welded areas primed and painted too then double that figure I would say. If you want hinges and doors so the kids/dogs/hampsters/whatevers can't fall in then double it again! Link to comment Share on other sites More sharing options...
loubyscooby Posted August 26, 2016 Author Report Share Posted August 26, 2016 Cheers Mike Just need the panels cutting and welding into place so thanks. Don't have to worry about anyone falling in, well except me. Link to comment Share on other sites More sharing options...
MtB Posted August 26, 2016 Report Share Posted August 26, 2016 (edited) So how much were you quoted then? Does my estimate support their prices or have I made them look cheap?! Why do you need it done anyway? Would canvas 'dodgers' do the job just as well perhaps? Edited August 26, 2016 by Mike the Boilerman Link to comment Share on other sites More sharing options...
bag 'o' bones Posted August 26, 2016 Report Share Posted August 26, 2016 (edited) assuming the panel is a basic square shape you could always fix an aluminium panel using self tapping screws. Looking at the picture again Mikes canavas dodger suggestion could look better than solid panels. Similar to this: http://www.svchapaai.com/wp-content/uploads/2015/06/P5160497.jpg What were you quoted for the welding? Edited August 26, 2016 by bag 'o' bones Link to comment Share on other sites More sharing options...
Tony Brooks Posted August 26, 2016 Report Share Posted August 26, 2016 The likes of Screwfix sell 5.5mm self drilling and self tapping hexagon set screws. You could use these to fix lengths of angle iron under the handrail. That will then give you the possibility of fixing steel, aluminium or sink down-sheets between the angle iron the the up-stand around the cockpit (if you have one). I used small nuts and bolts at the top and to join panels and the 5.5mm self drill/tap things into the up-stand. This what I have done on my boat because I think old faded, wrinkled and stained dodgers just look awful. At least I can give mine a quick coat of paint. Link to comment Share on other sites More sharing options...
MtB Posted August 26, 2016 Report Share Posted August 26, 2016 assuming the panel is a basic square shape you could always fix an aluminium panel using self tapping screws. The panels almost certainly won't be rectangular. The handrail supporting pillars slope inwards so the panels will be truncated pyramid-shaped. Obtaining the steel and cutting it into panels the right shape will be most of the work. Actually welding the correctly cut panels into place will be a breeze! Link to comment Share on other sites More sharing options...
Paul C Posted August 26, 2016 Report Share Posted August 26, 2016 You know it won't prevent you from falling in........there has been at least 1 fatality caused by the "fencing" on the back of a cruiser stern boat - basicaly its the ideal height to flip you over if the boat hits something backwards, especially if hitting eg the bank causes the rudder to turn sharply and this swings the tiller forcibly - hence the advice to keep out the arc of the tiller, especially in reverse. If you can fall in in between the gap of the horizontal rail and the deck, you deserve a job in the circus as a contortionist. If its for pets etc and a modification more for whilst mooring 99% of the time, then fair enough though. Link to comment Share on other sites More sharing options...
Murflynn Posted August 26, 2016 Report Share Posted August 26, 2016 I think old faded, wrinkled and stained dodgers just look awful. an old faded wrinkled dodger? are you referring to MTB or someone else? Link to comment Share on other sites More sharing options...
Featured Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now